Kismet On Windows Guide V0.2 - Page 5

renderman · 09-22-2005

Quote:

Originally Posted by theprez98

renderman,

I'm on step six of your guide.

When I try to run the drone, I get:

I'm guessing I messed up on step three where I was supposed to edit the kismet_drone.conf file?!

Step 3.2, you need to specify your source in the kismet.conf, depending on the version of your router

renderman · 09-22-2005

I'm geeting a 3d lock with my Garmin Etrex Legend. I'm not with my simulator.

At any rate, the cyg-gpsd seems to be playing nice with my GPS. Maybe you guys have some oddball units. Do you get a 3d lock under linux native?

Of course, right now I'm testing with some really cool toys I was sent, and I'm impressed it's working at all. I'll hopefully be able to share in a couple weeks, and render alot of the hard work getting this stuff working un-nessecary (but the research is valuable)

theprez98 · 09-23-2005

Quote:

Originally Posted by renderman

Step 3.2, you need to specify your source in the kismet.conf, depending on the version of your router

Ok, I'll have to re-check to make sure what version I have. I know it's the one with the "flashing" Cisco logo, probably the newest.

Edit: I think I have a v4. I'll have to check the serial # when I get home to be sure.

renderman · 09-23-2005

Quote:

Originally Posted by theprez98

Ok, I'll have to re-check to make sure what version I have. I know it's the one with the "flashing" Cisco logo, probably the newest.

Edit: I think I have a v4. I'll have to check the serial # when I get home to be sure.

Hmm, I don't have V4 yet. guess who gets to be a guinea pig

I think the V3 method should work, let me know if it does;nt

theprez98 · 09-23-2005

Quote:

Originally Posted by renderman

Hmm, I don't have V4 yet. guess who gets to be a guinea pig

I think the V3 method should work, let me know if it does;nt

I confirmed by serial number that I do in fact have a v4. I'll follow the v3 method tonight when I get home, and let you know how it goes.

renderman · 09-23-2005

Quote:

Originally Posted by Mark57

Long night. We lost cooling to our main data center. Had to scrounge fans, lots of them. I'm cooked. It was only 145 degrees in there.

Good way to loose weight temporarily.

I now have GPSD running with Kismet under Cygwin. Good job guys!

Did you have to add any packages? Just trying to confirm I listed everything needed

Mark57 · 09-23-2005

Quote:

Originally Posted by renderman

Did you have to add any packages? Just trying to confirm I listed everything needed

No. The list was good. Seems like one or two items were under different subcategories though. No biggie, just housekeeping.

renderman · 09-23-2005

Ok, updated just about everything today to reflect all the crzy work that's been going on.

http://www.renderlab.net/projects/wr...onwindows.html - kismet on windows guide is up to V3

I've also published the GPSD guide at http://www.renderlab.net/projects/wr...onwindows.html
and linked it appropriately in the Kismet guide

I'm starting a new thread about GPSD on Cygwin to keep things seperate. Any chance someone can move posts around?

theprez98 · 09-24-2005

I started over from scratch with the Kismet Drone How-to, following the steps for the v3 even though I have the v4. Everything appears to have worked correctly, when I start the drone, I am seeing all the expected information, and finally "Allowing connections..."

Once I get kismet running under cygwin on the laptop, I'll pass along any further info.

So far, v3 instructions appear to work for the v4 WRT54G.

theprez98 · 09-24-2005

Ok, Kismet runs under cygwin.

However, the card isn't scanning, so I guess that's a configuration issue. I'll keep working on that, as well as gpsd.

Edit: Ok, kismet is connecting to the drone successfully now, but still not scanning.

theprez98 · 09-24-2005

Ok, here's the latest update.

1. I followed the setup procedure for WRT54G Kismet Drone, using the OpenWRT firmware. When I edited the kismet_drone.conf file, I used the settings for the v3.0 router:

PHP Code:


			
source=wrt54g,eth1:prism0,wrt54g

2. Next, I followed the procedures for Kismet on Windows. Absolutely no isses here at all.

3. I also set up gpsd but I have not tested it yet.

4. I made two scripts, scanme.sh and rundrone.sh. I can log into the router just fine. At that point, I run the scanme script and then the rundrone script. The kismet_drone starts up.

5. I run kismet under cygwin on my laptop, and it connects to the drone as evidenced by the messenge from the drone telling me it has accepted an incoming connection.

6. Kismet finds my wireless network ("WOPR") but does not scan.

7. Finally, after rebooting, I cannot even run the kismet_drone. I am getting a FATAL: ioctl: No such device error:

PHP Code:


			
root@OpenWrt:/# sh rundrone.sh

eth1: Invalid argument

disassoc

        Disassociate from the current BSS/IBSS.



Using alternate config file: /etc/kismet_drone.conf

Suid priv-dropping disabled.  This may not be secure.

No specific sources given to be enabled, all will be enabled.

Enabling channel hopping.

Disabling channel splitting.

NOTICE: Disabling channel hopping, no enabled sources are able to change channel.

Source 0 (wrt54g): Enabling monitor mode for wrt54g source interface eth1:prism0

 channel 0...

Source 0 (wrt54g): Opening wrt54g source interface eth1:prism0...

FATAL: ioctl: No such device

Any ideas?

renderman · 09-24-2005

Quote:

Originally Posted by theprez98

Ok, here's the latest update.

1. I followed the setup procedure for WRT54G Kismet Drone, using the OpenWRT firmware. When I edited the kismet_drone.conf file, I used the settings for the v3.0 router:

PHP Code:


			
source=wrt54g,eth1:prism0,wrt54g

2. Next, I followed the procedures for Kismet on Windows. Absolutely no isses here at all.

3. I also set up gpsd but I have not tested it yet.

4. I made two scripts, scanme.sh and rundrone.sh. I can log into the router just fine. At that point, I run the scanme script and then the rundrone script. The kismet_drone starts up.

5. I run kismet under cygwin on my laptop, and it connects to the drone as evidenced by the messenge from the drone telling me it has accepted an incoming connection.

6. Kismet finds my wireless network ("WOPR") but does not scan.

7. Finally, after rebooting, I cannot even run the kismet_drone. I am getting a FATAL: ioctl: No such device error.

Any ideas?

The ioctl is probobly related to the dynamic creation of the 'prism0' interface. Make sure your issuing the 'wl ap 0' command before you fire up the drone. The drone will only work if it's in Client mode.

My suggestion would be to step through the commands in the rundrone.sh script, then try running the drone with a '&' at the end, so that after you connect with kismet, run 'wl scan' and see if it scans.

The other thing to check is the indents in scanme.sh, make sure that the 2 lines after 'do' are indented

theprez98 · 09-24-2005

Quote:

Originally Posted by renderman

The ioctl is probobly related to the dynamic creation of the 'prism0' interface. Make sure your issuing the 'wl ap 0' command before you fire up the drone. The drone will only work if it's in Client mode.

My suggestion would be to step through the commands in the rundrone.sh script, then try running the drone with a '&' at the end, so that after you connect with kismet, run 'wl scan' and see if it scans.

The other thing to check is the indents in scanme.sh, make sure that the 2 lines after 'do' are indented

Well, this is just weird because it worked before, and after rebooting the router I'm getting the error now.

When I run through the commands in the rundrone.sh script:
'wl ap 0'
'wl disassoc' returns "eth1: Invalid argument, Disassociate from the current BSS/IBSS."
'wl passive 1'
'wl promisc 1'
'chmod 777 /usr/bin/kismet*'
'usr/bin/./kismet_drone -f /etc/kismet_drone.conf &' returns the same FATAL: iotcl: No such device error.

It seems to me like I must be messing something up in the kismet_drone.conf file.

Edit: I started over from scratch with the kismet_drone install, but same results. So close...

Edit part 2: When I changed "eth1" to "eth0" the drone starts up (albeit with some errors) and I can connect to it from my laptop. It does see my wireless network. However, it is still not scanning. I ran the drone with &, and tried 'wl scan' but no luck there.

renderman · 09-24-2005

Quote:

Originally Posted by theprez98

Edit: I started over from scratch with the kismet_drone install, but same results. So close...

Edit part 2: When I changed "eth1" to "eth0" the drone starts up (albeit with some errors) and I can connect to it from my laptop. It does see my wireless network. However, it is still not scanning. I ran the drone with &, and tried 'wl scan' but no luck there.

Hmm, might be an issue with the V4's. I have'nt got one so I can't test. No budget to go out and get one. Any way you could get me telnet/ssh access to it? Anyone want to send me one?

theprez98 · 09-25-2005

Quote:

Originally Posted by renderman

Hmm, might be an issue with the V4's. I have'nt got one so I can't test. No budget to go out and get one. Any way you could get me telnet/ssh access to it? Anyone want to send me one?

I'll see if I can get it set up. I'm fairly convinced it is some sort of configuration file error on my part.

09-22-2005	#62 (permalink)
renderman Drunken Stumbler Join Date: Jun 2002 Location: Anywhere but Utah Posts: 1,792	I'm geeting a 3d lock with my Garmin Etrex Legend. I'm not with my simulator. At any rate, the cyg-gpsd seems to be playing nice with my GPS. Maybe you guys have some oddball units. Do you get a 3d lock under linux native? Of course, right now I'm testing with some really cool toys I was sent, and I'm impressed it's working at all. I'll hopefully be able to share in a couple weeks, and render alot of the hard work getting this stuff working un-nessecary (but the research is valuable) __________________ Never drink anything larger than your head! Scaramental Wine Taster for the Church Of WiFi Buy our book: RFID Security "I reject your reality, and substitute my own!" – Adam Savage CoWF WPA Hash Tables

09-23-2005	#68 (permalink)
renderman Drunken Stumbler Join Date: Jun 2002 Location: Anywhere but Utah Posts: 1,792	Ok, updated just about everything today to reflect all the crzy work that's been going on. http://www.renderlab.net/projects/wr...onwindows.html - kismet on windows guide is up to V3 I've also published the GPSD guide at http://www.renderlab.net/projects/wr...onwindows.html and linked it appropriately in the Kismet guide I'm starting a new thread about GPSD on Cygwin to keep things seperate. Any chance someone can move posts around? __________________ Never drink anything larger than your head! Scaramental Wine Taster for the Church Of WiFi Buy our book: RFID Security "I reject your reality, and substitute my own!" – Adam Savage CoWF WPA Hash Tables

09-24-2005	#69 (permalink)
theprez98 SpoonfeederExtraordinaire Join Date: Jan 2005 Location: Maryland Posts: 3,622	I started over from scratch with the Kismet Drone How-to, following the steps for the v3 even though I have the v4. Everything appears to have worked correctly, when I start the drone, I am seeing all the expected information, and finally "Allowing connections..." Once I get kismet running under cygwin on the laptop, I'll pass along any further info. So far, v3 instructions appear to work for the v4 WRT54G. __________________ :00475160 0E A6 AE A0 19 E3 A3 46 .......F :00475168 0D 65 17 0C 53 70 6F 6F .e..Spoo :00475170 6E 66 65 65 64 65 72 2E nfeeder. :00475178 45 78 74 72 61 6F 72 64 Extraord :00475180 69 6E 61 69 72 65 5D 3B inaire]; :00475188 8B 9E 92 5A FF 5D A6 F0 ...Z.]..

09-24-2005	#70 (permalink)
theprez98 SpoonfeederExtraordinaire Join Date: Jan 2005 Location: Maryland Posts: 3,622	Ok, Kismet runs under cygwin. However, the card isn't scanning, so I guess that's a configuration issue. I'll keep working on that, as well as gpsd. Edit: Ok, kismet is connecting to the drone successfully now, but still not scanning. __________________ :00475160 0E A6 AE A0 19 E3 A3 46 .......F :00475168 0D 65 17 0C 53 70 6F 6F .e..Spoo :00475170 6E 66 65 65 64 65 72 2E nfeeder. :00475178 45 78 74 72 61 6F 72 64 Extraord :00475180 69 6E 61 69 72 65 5D 3B inaire]; :00475188 8B 9E 92 5A FF 5D A6 F0 ...Z.].. Last edited by theprez98 : 09-24-2005 at 10:45 AM.

09-24-2005	#71 (permalink)
theprez98 SpoonfeederExtraordinaire Join Date: Jan 2005 Location: Maryland Posts: 3,622	Ok, here's the latest update. 1. I followed the setup procedure for WRT54G Kismet Drone, using the OpenWRT firmware. When I edited the kismet_drone.conf file, I used the settings for the v3.0 router: PHP Code: `source=wrt54g,eth1:prism0,wrt54g` 2. Next, I followed the procedures for Kismet on Windows. Absolutely no isses here at all. 3. I also set up gpsd but I have not tested it yet. 4. I made two scripts, scanme.sh and rundrone.sh. I can log into the router just fine. At that point, I run the scanme script and then the rundrone script. The kismet_drone starts up. 5. I run kismet under cygwin on my laptop, and it connects to the drone as evidenced by the messenge from the drone telling me it has accepted an incoming connection. 6. Kismet finds my wireless network ("WOPR") but does not scan. 7. Finally, after rebooting, I cannot even run the kismet_drone. I am getting a FATAL: ioctl: No such device error: PHP Code: root@OpenWrt:/# sh rundrone.sh eth1: Invalid argument disassoc Disassociate from the current BSS/IBSS. Using alternate config file: /etc/kismet_drone.conf Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Enabling channel hopping. Disabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (wrt54g): Enabling monitor mode for wrt54g source interface eth1:prism0 channel 0... Source 0 (wrt54g): Opening wrt54g source interface eth1:prism0... FATAL: ioctl: No such device Any ideas? __________________ :00475160 0E A6 AE A0 19 E3 A3 46 .......F :00475168 0D 65 17 0C 53 70 6F 6F .e..Spoo :00475170 6E 66 65 65 64 65 72 2E nfeeder. :00475178 45 78 74 72 61 6F 72 64 Extraord :00475180 69 6E 61 69 72 65 5D 3B inaire]; :00475188 8B 9E 92 5A FF 5D A6 F0 ...Z.].. Last edited by theprez98 : 09-24-2005 at 05:46 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode