Page 4 of 6

PostPosted: Sat May 29, 2004 11:36 am
by GuardianZX9
My 2215 works with the Ambicom WL-1100C-CF card with the Intersil Prism driver set, couldn't get it to work with the Ambisom driver.

G

IPAQ 5455 Internal WIFI Does Work

PostPosted: Sun May 30, 2004 4:28 pm
by Bananaskin
Greets to all

Confirming that my IPAQ 5455 running Pocket PC 2002 version 1.11.XX (06 Jun 03) D/L'd from the HP site does work. No updates were applied in the form of firmware or drivers for the wlan. Asset Viewer information is as follows:

Hardware Revision : 6.3
Firmware Version : 0.100.5.39
Driver Version : 3.2.2.84
Software Version : 4.0.1.36
Module Release Date : 02.09.05

PostPosted: Sat Jun 05, 2004 1:49 pm
by fordem
Came across a post on the Aximsite that says the Dell Axim X30 with the integrated wireless works - I'm not certain if this is different hardware or different drivers - the X30 does ship with WM2003SE.

Apparently the X30 uses the Dell TM1210 so I guess the different hardware is why it works.

PostPosted: Sun Jun 06, 2004 2:18 am
by PlaggyJohn
Ministumbler is OK on my old Cassiopeia E115 (CE 3.0) & Linksys WCF12

PostPosted: Thu Jun 10, 2004 7:16 am
by phantagom
I have a IPAQ 5450 and ministumbler works (sort of)

OS: WM2003

My Asset Viewer for WLAN says:
Hardware Version: 6.3
Firmware Version: 0.100.5.39
Driver Version: 3.2.2.96
Module release date: 02.09.05

But ministumbler doesn't detect as many AP's then wififofum. Wififofum detects up to 3 times more AP's then Ministumbler.

PostPosted: Thu Jun 10, 2004 7:25 am
by G8tK33per
phantagom wrote:I have a IPAQ 5450 and ministumbler works (sort of)

OS: WM2003

My Asset Viewer for WLAN says:
Hardware Version: 6.3
Firmware Version: 0.100.5.39
Driver Version: 3.2.2.96
Module release date: 02.09.05

But ministumbler doesn't detect as many AP's then wififofum. Wififofum detects up to 3 times more AP's then Ministumbler.
This is not a competition, either it works or not...just like the title of the thread states. If you're unhappy with the program, delete and move on.

PostPosted: Sun Jul 04, 2004 5:54 am
by GordonNL
hi there.. this works great with my h2210+Dell truemobile 1180...
but is there a way to set mij wifi card ON or OF? so i can always let my card in it?

PostPosted: Thu Jul 08, 2004 1:48 am
by SolarW
Work fine on my HP Jornada720 (HPC2000 ARM) with Orinoco Silver (Lucent technologies)

ipaq 5450

PostPosted: Thu Jul 08, 2004 5:52 am
by genexen
Just my $0.02 -

My ipaq 5450 (PPC 2002) works great with MS 0.4 on the integrated wlan card. No issues experienced installing or configuring.

Unit ROM 1.11.19 ENG
Wlan hw: 6.3
wlan fw: 0.100.5.39

Axim / D-Link / MS 0.4

PostPosted: Tue Jul 20, 2004 3:00 pm
by G8tK33per
Works like a charm:

Axim X5 Advanced PPC2K2
D-Link DCF-660W
MS 0.4

ASUS SpaceLink WF-110

PostPosted: Fri Jul 23, 2004 12:08 am
by short_ms
ministumbler on my jornada 525 works great with the asus cf-card. no problems with configuration or installation, just plug'n'play.

PostPosted: Fri Jul 23, 2004 12:19 am
by KREE
Works with my 2210 ipaq and DCF-660W, really well. Only problem is I can't obtain an ip address on my home network, my suspision is that I have disabled the ip stack as recomended in Wardriving: Drive, Detect, Defend, So no big deal as I enjoy wardriving more than surfing the internet on my ppc. Great program marius, and great book chris, thorn, & mother. Alot of learning going on here.

PostPosted: Mon Aug 09, 2004 9:04 pm
by xtra
to people have ma701 work with ministumbler .4, what version of driver you running?

i used 1.1 driver, but ministumbler couldnt find wireless card. if i upgrade to the 2.0 driver, the wireless card is detected but it couldnt find any APs.

any thoughts, guys? I have an axim x5 basic.

PostPosted: Wed Aug 11, 2004 12:37 pm
by Gramzster
I have a HP iPAQ 2215 and the Sandisk 256MB+Wifi SDIO card.

Works great with ministumbler.

Jornada 525 & D-Link DCF-660W

PostPosted: Wed Aug 11, 2004 1:31 pm
by 5.9 Limited
:confused:
nightowl8 wrote:Works on Jornada 525 (SH3) with D-Link DCF-660W (CF Card).


I have the same set-up but I can't get it to work. Could you walk me through this please? Thank you.